Search Results

The continuous decrease in background noise levels inside vehicles has made other noise sources easily noticeable. Specifically, foundation brake rattle noise is a growing concern to the customer. This brake rattle is primarily due to rigid body impact between brake components. Currently, vehicle and brake manufacturing companies use different testing procedures to evaluate brake rattle that include laboratory vibration shakers, full vehicle shakers (four post), chassis dynamometers and vehicle road testing. These evaluations are subjective in most cases. A method is needed to replicate and quantify vehicle brake rattle in the laboratory to help determine the acceptability of a brake system at a component level. This approach would also help to identify the root cause for brake rattle and evaluate design changes to address that rattle. Some guidelines for better quantifying brake rattle using shakers will be proposed in this paper.

Customers of new vehicles expect their vehicle to provide reliable operation. One path vehicle manufacturers have chosen to meet this expectation is to offer their customers advanced braking systems. Antilock Brakes (ABS) and Traction Control (TC) are two advanced braking systems that have evolved to a point at which many OEM's offer them as standard equipment. Size, weight, and performance have also improved to the point of near transparent operation in many cases. The current direction of braking system evolution is in making Vehicle Stability Control (VSC) widely available as well. VSC adds the ability to assist the driver in negotiating understeer and oversteer, by adding corrective braking and engine torque to the vehicle as appropriate. A large percentage of VSC system modeling is related to the sensors chosen to provide driver and vehicle dynamic information to the system's electronic control unit (ECU).

A new algorithm for carrier removal, a key step in the Fourier transform method of fringe pattern analysis, is presented in this paper. The accuracy of frequency estimations is critical to carrier removal to avoid potential significant errors in the recovered phase. A new algorithm on Fourier transform and curve fitting technique is developed. To avoid an ill-conditioned result in solving the least-square problem, an orthogonal polynomial curve fitting algorithm is developed. A new system that combines projected grating moiré (PM) with shadow moiré (SM), recently designed and built with large dynamic range for both component level and board level warpage measurement for the reliability study of electronic packaging materials and structures, is presented and demonstrated.

This paper presents a computer model for simulating dynamic responses inside an injector of an automotive fuel rail system. The injector contains a filter at the top, a coil spring in the middle, and a needle and orifices at the bottom. The equations of motion for unsteady one-dimensional flow are derived for the fluid flowing through the injector. The needle motion is described by a second order ordinary differential equation. The forces exerted on the needle include the magnetic force that controls the opening and closing of the injector and the coil spring force. To account for the loss of kinetic energy, we define two loss factors Ka and Kb. The former describes the loss of kinetic energy as fluid enters the injector through the filter at the top, and the latter depicts that as fluid is ejected into a large chamber through the passage between the needle and the needle seat and across four orifices at the bottom of the injector.

In a frontal automotive crash, the driver's foot is usually stepping on the brake pedal as an instinctive response to avoid a collision. The tensile force generated in the Achilles tendon produces a compressive preload on the tibia. If there is intrusion of the toe board after the crash, an additional external force is applied to the driver's foot. A series of dynamic impact tests using human cadaveric specimens was conducted to investigate the combined effect of muscle preloading and external force. A constant tendon force was applied to the calcaneus while an external impact force was applied to the forefoot by a rigid pendulum. Preloading the tibia significantly increased the tibial axial force and the combination of these forces resulted in five tibial pylon fractures out of sixteen specimens.

Recently, during the course of different experimental problem-solving activities on automotive vehicles, several examples have been found in which the identification of the cause of a particular vibration problem related to a specific component or subsystem involves detecting the presence of an impulsive effect on measured time signals. The difficulty in identifying such an effect arises due to the fact that the vibrational response signals measured during operation are dominated by relatively high amplitude harmonics which tend to mask the impulsive component. This article describes two case studies for this type of identification problem, a servo-assisted steering system and a front suspension shock absorber strut.

We have prepared and tested laboratory scale monoliths wash-coated with 10, 20 and 30 wt% of either CeO2 or Ce.75Zr.25O2 (remainder is alumina). Wet impregnation was used to load the wash-coated monoliths with 50g/ft Pt:Rh at a 5:1 ratio. The catalyst were aged at temperatures between 825°C and 950°C using a cycled redox aging. The catalysts were then tested in a full-feed simulated exhaust laboratory reactor with air-to-fuel ratio (A/F) perturbations (frequencies at 1 and 3 Hz and amplitudes up to +/- 0.8 A/F). Even the lowest loading of Ce.75Zr.25O2 outperformed all three loadings of CeO2 over a full range of reaction temperatures, A/F perturbations, and catalyst space velocity (SV). Our data indicates that the ceria-zirconia catalysts can tolerate cycled redox aging at sustained bed temperatures at least 25°C higher (∼925°C vs. < 900°C) than can ceria. For the CeO2 catalysts aged at or above 900°C we observed an inverse correlation of catalyst activity to CeO2 loading.

The boundary integral equation method (BIEM) of analysis was applied to problems involving beams, thick plates and stress concentration regions. Beam and plate problems were considered to provide guidelines for use of the three-dimensional BIEM to analyze brackets and other components which have “solid like” regions as well as regions which are “beam or plate like”. In unsubstructured form the BIEM produced results in excellent agreement with exact solutions from elasticity theory for plates with length/thickness ratios as large as 40. Loading cases included bending by terminal couples and flexure by terminal loads. Using substructuring, CP times were reduced. CP times for both the IBM 3084 and the CDC CYBER 205 were obtained, the influence of varying integration orders discussed, and techniques to assess the accuracy of computed results were described.

An improved windshield with a special, thin, plastic inner surface attached to the inner surface of a three layer windshield similar to those used in the United States minimizes lacerations from occupant impact to the windshield during a collision. The plastic coats the sharp edges of the broken glass preventing or minimizing laceration. It was evaluated by comparing its laceration performance with that of a standard windshield in simulated barrier crashes at velocities up to 65 km/h. No lacerations resulted from impact to the Securiflex windshield at Barrier Equivalent Velocities up to 65 km/h. Substantial laceration resulted at velocities above 20 km/h with the standard windshield. It is concluded that the Securiflex windshield essentially eliminates lacerations in the particular vehicle involved at velocities up to at least 65 km/h.

The effects of several faults on different parameters in a distributor injection system are studied both theoretically and experimentally. The faults imposed on a healthy system are: fuel leaks between the pump and injector, improper adjustment of the injector opening pressure, a broken or missing injector spring, plugged nozzle holes, and a stuck-closed needle. The injector parameters examined include maximum fuel pressures reached at different locations in the system, needle lift, injection lag, and injection rate.

A human head model has been developed primarily for use in evaluation of impact attenuation properties of football helmets, but is also applicable in automobile impact safety tests. Using firm silicon rubber molds made from impressions of cadaver bones, a skull and mandible were each cast in one piece using a self-skinning urethane foam that hardens into cross section geometry similar to the human bone. A rubber gel material is used to simulate the brain. The skull and attached mandible are overlayed with repairable silicon rubber skin having puncture and sliding-over-bone characteristics similar to human skin. At present, the model has a rudimentary solid silicon rubber neck, through the center of which runs a flexible steel cable attached at the foramen magnum. The cable is used to attach the head to a carriage or anthropometric dummy and can be adjusted in tension to give various degrees of flexibility.